Tungsten carbide/ Boron carbide nozzle for sand blasting machines
Sand Blasting Boron Carbide Nozzle
High hardness, Low density, High temperature resistant, Excellent
wear and anti-corrosion.
Specifications
a) High abrasion resistance, high using life.
b) High hardness and high strength
c) High chemical corrosion.
d) Light weight
Sand Blasting Boron Carbide Nozzle
This kind of nozzle is made from boron carbide by hot pressing with
straight bore and venturi bore type. Because of its hardness, low
density, high temperature resistance, excellent wear and
anti-corrosion, Boron Carbide Nozzle has been widely used in
sandblasting and shot peening equipments, offering a longest life
with optimum air and abrasive use.
Products application:
Equipped on the blasting machine and used as sand blasting.
Can be used to remove rust, water cutting etc.
Product features:
High abrasion resistance, high using life
High hardness and high strength
High chemical corrosion
Light weight
Advantages
1. Longer service life. In terms of service life, boron carbide
nozzle has the longest one such as for sand
blasting and shot peening.
2. Lower cost per use. Boron carbide costs more but will outlast
tungsten carbide by 3 to 10times.
3. To reduce down time.
4. To maintain efficiency.
Company Principle:
Our Belief: Continuous Innovation.
Our Spirit: Sincerity, Unity, Dedicated, Hardworking.
Our Mission: Provide most advanced products & most professional
technical solution.
Divided Venturi nozzle structure contraction section, straight
sections and diffusion segment of three parts, aerodynamic
performance is superior to straight bore nozzle, vortex phenomenon
is significantly improved or ceased to exist, the pressure loss is
greatly reduced, at the same pressure conditions, increase exports
to more than double the speed of the abrasive, work efficiency
increased by 15% -40% compared to straight bore nozzle, abrasive
consumption reduced by 20%.
Single inlet nozzle is a time into the wind. Double inlet is the
second into the wind, before and after the two nozzles, there is
space betwe Cen the two, at around eight holes at intervals, in
such a large and one small, the nozzle arrangement in a previous
post, As the role of the high-speed air stream to produce a
sufficiently large negative pressure, air is drawn into the nozzle,
the discharged air is greater than the compressed air into the
nozzle outlet velocity abrasive increased again. In addition,
double inlet jet produced sand lance end diameter larger than a
single into a number of wind divergence surface abrasive stream
into 30% larger than a single wind, higher cleaning efficiency.
Sandblasting gun thread specification:
Standard inch thread: 1-1/4 ,11-1/2 N.P.S.M.
Coarse thread: 2 ,4-1/2 U.N.C.
Inside diameter
|
Outside diameter
|
Length
|
| 1/4 Inch (6.4mm) | 1-5 /8 Inch (36mm) | 130mm
|
| 5/16 Inch(7.9mm) | 1-5 /8 Inch (36mm) | 150mm
|
| 3/8 Inch (9.5mm) | 1-5 /8 Inch (36mm) | 170mm
|
| 7/17 Inch(11.1mm) | 1-5 /8 Inch (36mm) | 200mm
|
| 1/2 Inch (12.7mm) | 1-5 /8 Inch (36mm) | 210mm |
Contact us:
Lucky Liu
E-mail: highbroad1@vip.163.com
Telephone: +86-731-85717705
Mobile Phone:+86-15575935462
Address: 70 Chezhan North Road,Changsha,Hunan
